Hansa Chippers

Reliability

Easy to use

High throughput, efficient operation

Maneuverablily

Simple to maintain & service

Unrivalled availability of components

Made in New Zealand for New Zealand conditions

Hansa C3e Chipper

Features

  • One in feed chute with large opening at a  convenient operating height
  • Powered by 2HP single phase electric motor
  • Capacity of 30mm branch diameter
  • Push button start with thermal overload
  • Conforms to ASNZS62841.1-2015 standard
  • Discharge out the side directly back onto your garden or stockpile or into optional bag (as shown in image above)
  • Solid housing construction of 5mm steel plate
  • Easy access to cutting blade – remove four bolts and everything is accessible
  • Easy to transport, well balanced on large solid rubber wheels
  • Will handle flax, cabbage tree leaves and palm fronds without wrapping around the rotor shaft
  • Quality powdercoated finish (media blasted surface for excellent adhesion)
  • 12 month warranty (extended warranty to 24 months on registration)
  • New Zealand made for New Zealand conditions

Price: $1,295.00 including GST

 

Hansa C4 Chipper

Features

  • One in feed chute with large opening at a  convenient operating height
  • Quality engine – Honda 4 stroke GX160
  • Capacity of 40mm branch diameter
  • Easy starting
  • Discharge out the side directly back onto your garden or stockpile or into optional bag (as shown in image above)
  • Solid housing construction of 5mm steel plate
  • Easy access to cutting blade – remove four bolts and everything is accessible
  • Easy to transport, well balanced on large solid rubber wheels
  • Will handle flax, cabbage tree leaves and palm fronds without wrapping around the rotor shaft
  • Quality powdercoated finish (media blasted surface for excellent adhesion)
  • 12 month warranty (extended warranty to 24 months on registration)
  • New Zealand made for New Zealand conditions

Price: $2,095.00 including GST

Hansa C7 Chipper

Features

  • One in feed chute with large opening at convenient operating height
  • Quality engine – Honda 4 stroke GX200
  • Self-feeding action, capacity of 70mm branches
  • Easy starting with soft start technology and twin belt drive
  • High discharge into trailer, wheelbarrow or stockpile
  • Solid housing construction of 5mm steel plate
  • Easy to transport, well balanced on large pneumatic wheels
  • Easy access to knives and clearing of housing – a few turns of the wingnut and everything is accessible within seconds
  • Quality powdercoated finish (media blasted surface for excellent adhesion)
  • 12 month warranty (extended warranty to 24 months on registration)
  • New Zealand made for New Zealand conditions

Price: $2,995.00 including GST

Hansa C13 Chipper

Features

  • One in feed chute with large opening at convenient operating height
  • Quality engine - Honda 4 stroke GX390
  • Self-feeding action, capacity of 80 – 90mm
  • Solid housing construction of 5mm steel plate
  • Easy starting with soft start technology and twin belt drive
  • High discharge into trailer, wheelbarrow or stockpile
  • Quality powdercoated finish (media blasted surface for excellent adhesion)
  • 12 month warranty (extended warranty to 24 months on registration)
  • New Zealand made for New Zealand conditions

Price: $6,400.00 including GST

Hansa C16 Chipper

Features

  • Self-feeding cutting action.
  • Powered by 16HP Briggs and Stratton Vanguard engine - recoil start
  • Large infeed chute allows full branches to flow into the machine. No pre-cutting necessary.
  • Rotating outlet chute for 270° discharge with deflector. The positive locking system requires no tools.
  • Easy starting with soft start technology.
  • Twin beltdrive for smooth running and protection against shock load.
  • Easy access to the knives and the inside of the housing, just by swinging back the outlet chute.
  • Duratorque axle suspension.
  • Quality powdercoated finish (media blasted surface for excellent adhesion).
  • 12 month warranty.
  • New Zealand made for New Zealand conditions.

Price: $11,800.00 including GST

Hansa C21 Chipper

Features

  • Self-feeding cutting action.
  • Powered by 21HP Honda engine electric start or tractor mounted PTO driven
  • Large infeed chute allows full branches to flow into the machine. No pre-cutting necessary.
  • Rotating outlet chute for 270° discharge with deflector. The positive locking system requires no tools.
  • Easy starting with soft start technology.
  • Twin beltdrive for smooth running and protection against shock load.
  • Easy access to the knives and the inside of the housing, just by swinging back the outlet chute.
  • Duratorque axle suspension.
  • Quality powdercoated finish (media blasted surface for excellent adhesion).
  • 12 month warranty (extended warranty to 24 months on registration).
  • New Zealand made for New Zealand conditions

Price: $17,850.00 including GST

Hansa C27 Chipper

Features

  • 360 degree turntable: Allows feeding from any direction, all while still being coupled and discharging into your tow vehicle.

  • Wide Infeed Opening: 330 x 178mm (13” x 7”). Excellent for processing foliage and brushy material.
  • Compact design: Maneuverable and versatile. With the inlet chute rotated over the drawbar the total length is 2600mm.
  • Vertical Anvil: Anvil positioned vertically (rather than horizontally) to reduce knife damage caused by abrasive material.
  • Hydraulic Pump: Driven off the engine. Even if cutting disk is jammed, the feed roller can still be reversed for clearing the branch material.
  • Clutch: Easy starting with soft start technology. Simple and reliable.
  • Outlet: 360° rotating chute with deflector and a positive locking system. No tools required for adjustments.
  • Jockey Wheel: Large solid wheel, height adjustable.
  • Light System: LED tail, brake and license plate lights, suitable for 12 or 24 volt system.
  • Feed Roller: Pivot type spring tensioned, operates with less friction, moves within 10mm of knives.
  • Feed Control Bar: Pull to feed, push for reverse.
  • Feed Table: Folds away and is locked when transporting the machine.
  • Auto Sensor Feed: Electronically monitors engine RPM and controls feed roller to suit. Auto feed is operator adjustable by push button, LCD screen displays engine RPM & hour meter.
  • Finish: Media blasted surface, zinc shielded and powdercoated (Hansa green or optional colour of your choice).
  • Warranty: 12 month warranty (conditions apply).
  • New Zealand made for New Zealand conditions.

Price: $33,925.00 including GST

Hansa C40 Chipper

Features

  • Wide Infeed Opening: 330 x 178mm (13” x 7”). For foliage and brushy material, this wide infeed opening gives the chipper a capacity of a 10” to 12” machine with all the advantages of a 7” machine, e.g. Low weight and cost, and easy to manouvre.
  • Vertical Anvil: Anvil positioned vertically (rather than horizontally) to reduce knife damage caused by abrasive material.
  • Hydraulic Pump: Driven off the engine. Even if cutting disk is jammed, the feed roller can still be reversed for clearing the branch material. 
  • Clutch: Easy starting with soft start technology. Simple and reliable. Auto tensioning belt drive system.
  • Outlet: 360° rotating chute with deflector and a positive locking system. No tools required for adjustments.
  • Jockey Wheel: Large solid dual wheels, height adjustable.
  • Light System: LED tail, brake and license plate lights, suitable for 12 or 24 volt system.
  • Feed Roller: Pivot type spring tensioned, operates with less friction, moves up to within 10mm of knives.
  • Feed Control Bar: Pull to feed, push for reverse.
  • Feed Table: Folds away and is locked when transporting the machine.
  • Auto Sensor Feed: Electronically monitors engine RPM and controls feed roller to suit. Auto feed is operator adjustable by push button, LCD screen displays engine RPM & hour meter. Auto reversing for quicker engine recovery. Feedroller jams are reversed and cleared automatically, eliminating manual reversing of feedroller if a blockage occurs. .
  • Finish: Media blasted surface, zinc shielded and powdercoated (Hansa green or optional colour of your choice).
  • Warranty: 12 month warranty (conditions apply)
  • New Zealand made for New Zealand conditions.

Price: $42,550.00 including GST

Hansa C60 Chipper

Features

  • Wide Infeed Opening: 254 x 457mm (10”x18”), excellent for processing foliage, brushy and forked branches
  • Vertical Anvil: Anvil positioned vertically (rather than horizontally) to reduce knife damage caused by abrasive material.
  • Hydraulic Pump: Connected to the auxilary drive of the engine. Even if cutting disk is jammed, the feed roller can still be reversed for clearing the branch material.
  • Clutch: Easy starting with soft start technology. Simple and reliable. Auto tensioning belt drive system.
  • Pivot Outlet Chute: Outlet chute can be pivoted vertically by 260mm to suit your truck height or your desired outlet height.
  • Outlet: 360° rotating chute with deflector and a positive locking system. No tools required for adjustments.
  • Jockey Wheel: Large solid wheel, height adjustable.
  • Light System: LED tail, brake and license plate lights, suitable for 12 or 24 volt system.
  • Feed Roller: Pivot type, operates with less friction, moves forward and up to within 10mm of knives.
  • Feed Control Bar: Pull to feed, push for reverse.
  • Feed Table: Folds away and is locked when transporting the machine.
  • Auto Sensor Feed: Electronically monitors engine RPM and controls feed roller to suit. Auto feed is operator adjustable by push button, LCD screen displays engine RPM & hour meter. Auto reversing for quicker engine recovery. Feedroller jams are reversed and cleared automatically, eliminating manual reversing of feedroller if a blockage occurs.
  • Finish: Media blasted surface, zinc shielded and powdercoated (Hansa green or optional colour of your choice).
  • Warranty: 12 month warranty (conditions apply).
  • New Zealand made for New Zealand conditions.

Price: $54,625.00 including GST

Hansa C60RX Tracked Brush Chipper

Features

  • Tracked undercarriage - fully proportional remote controlled standard
  • Wide Infeed Opening: 254 x 457mm (10”x18”), excellent for processing foliage, brushy and forked branches
  • Vertical Anvil: Anvil positioned vertically (rather than horizontally) to reduce knife damage caused by abrasive material.
  • Hydraulic Pump: Belt driven off the engine. Even if cutting disk is jammed, the feed roller can still be reversed for clearing the branch material.
  • Clutch: Easy starting with soft start technology. Simple and reliable. Auto tensioning belt drive system.
  • Pivot Outlet Chute: Outlet chute can be pivoted vertically by 260mm to suit your truck height or your desired outlet height.
  • Outlet: 360° rotating chute with deflector and a positive locking system. No tools required for adjustments.
  • Feed Roller: Pivot type, operates with less friction, moves forward and up to within 10mm of knives.
  • Feed Control Bar: Pull to feed, push for reverse.
  • Feed Table: Folds away and is locked when transporting the machine.
  • Auto Sensor Feed: Electronically monitors engine RPM and controls feed roller to suit. Auto feed is operator adjustable by push button, LCD screen displays engine RPM & hour meter. Auto reversing for quicker engine recovery. Feedroller jams are reversed and cleared automatically, eliminating manual reversing of feedroller if a blockage occurs.
  • Finish: Media blasted surface, zinc shielded and powdercoated (Hansa green or optional colour of your choice).
  • Warranty: 12 month warranty (conditions apply).
  • New Zealand made for New Zealand conditions.

Price: $81,650.00 including GST